I don’t have an answer but you can rest assured, if the result is not what you had hoped, a little elbow grease and water and you can remove it.
-
The Fedora Lounge is supported in part by commission earning affiliate links sitewide. Please support us by using them. You may learn more here.
Ask a Question, Get An Answer About Outerwear
- Thread starter Marc mndt
- Start date
Be careful with deer! Many conditioners will not penetrate, and will either harden it or make it "gummy". I had some luck using Skidmores, but it did coat the hide with wax. Something like Obenauf's oil could do the trick. ***use it very sparingly***
Looks like oil? If so, it’s there forever. Naked leathers will keep that even if dyed.
Featured products
-
Alden 403 Moc Toe Boot - Brown Chromexcel - $680 The classic "Indy" style Alden Boot in the classic Horween brown Chromexcel. -
Grant Stone Diesel Boot Dark Olive Chromexcel - #395 Goodyear welted, Horween Chromexcel, classic good looks. -
Himel Bros. - The Ross Mk. 1 Leather Jacket Classic D-pocket motorcycle/aviator style jacket.
Bluechel
Practically Family
- Messages
- 993
Crap! Oh well, experiment time….
Bluechel
Practically Family
- Messages
- 993
Maybe I’ll try brown Urad….
No! Not on deerskin!
Observe
One Too Many
- Messages
- 1,208
Got a Taylor's police jacket that has the collar points stitched to the body of the jacket. Think I can use a stitch ripper or something to undo this with minimal damage?
Observe
One Too Many
- Messages
- 1,208
Yeah, don't use Urad on soft, porous leather like deerskin, it'll totally change it. Use Tenderly if you want to stick to the same family of products.
I think you could easily just cut that knot, but a seam ripper will work too.
Bluechel
Practically Family
- Messages
- 993
Perhaps Tenderly…it’s sort of weird that there’s not a product….
Observe
One Too Many
- Messages
- 1,208
Badge removal from the sleeve of this jacket left a lot of perforations in the leather, which I'm concerned may begin to tear. What's the best course of action here? Leave it, patch over it with some leather, or patch under it to reinforce it from the back?
I think the way to repair such damage is to GLUE a patch of leather under it. I would send it to Dena. That perf looks fearsome.
Bluechel
Practically Family
- Messages
- 993
The design is ripe for an additional area of quilted leather right over it on both sides?
Good idea. Again, Dena would do a great job of it I think.
Observe
One Too Many
- Messages
- 1,208
I'm not much of a quilted leather guy, and I only spent $160 on the jacket so I'm hoping for the most cost effective repair possible. This probably precludes sending it away to a speciality leather shop. Here's a full pic of the jacket:
Think I could get a local tailor to glue a piece of leather underneath the area in question?
I will say, the leather on this old Taylor's police jacket is quite nice. Thick and supple.
Think I could get a local tailor to glue a piece of leather underneath the area in question?
I will say, the leather on this old Taylor's police jacket is quite nice. Thick and supple.
Nice jacket. Because the reinforcing leather patch would be on the inside, you can try to save some coin and do the reinforcing yourself. The best glue to connect two leather surfaces on their roughout side is rubber cement. The bond will be damn near unbreakable. If you decide that someone else should do the reinforcing, I would talk to a cobbler, not a tailor. A cobbler will dig the concept of a reinforcing patch in a second, and will know what glue to use.
Observe
One Too Many
- Messages
- 1,208
I have barge cement on hand and have used it for leather repair in the past, but maybe if I take it to a cobbler they'll have rubber cement to use.
I used Weldwood. Tbh, they are all similar. Some swear by Barge. This repair is non-critical (ie in non-stress area), so it won't matter. I would say the only important thing is to use a solvent-based cement, not the water-based crap. The solvent is what you smell when you walk into a cobbler's shop...
Similar threads
